Just how do you actually feel with regards to How to Install a Bathtub?
Mounting a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily obtainable, the job can move easily; if you have to open up a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a professional to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This post will certainly assist you mount a new bath tub in your bathroom if you have actually already gotten a brand-new tub and also don't need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist need to comprise the following:
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the tub in the required placement. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bath tub until the level checks out degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water system and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has been used a minimum of when as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind must be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath and the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to allow for the motion experienced when the tub is in usage. The sealant can split fairly very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is suggested to fit the tiles utilizing water-resistant or water resistant adhesive as well as cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Do you enjoy reading about How to Install a Bathtub Yourself? Give feedback directly below. We would be delighted to hear your reactions about this review. Hoping that you come back again soon. Remember to take the time to promote this post if you liked it. I love reading our article about Tools You Need to Install a New Bathtub .
Request A Quote